top of page

How to Select the Correct Mooring Bollard Capacity

Writer: ESC Steel LLC
ESC Steel LLC
2 hours ago
4 min read

Selecting the correct mooring bollard capacity is a critical part of designing a safe and reliable berthing facility. For ports, harbors, marine terminals, wharves, jetties, and other waterfront infrastructure across the United States and North America, bollards must safely resist vessel mooring forces and transfer those loads into the supporting structure.


Marine mooring bollards installed on a concrete pier for vessel berthing


Bollard capacity should not be selected based on vessel size or displacement alone. The correct rating depends on the design vessel, environmental loads, mooring arrangement, line angles, operating conditions, and structural capacity of the berth.




Understanding Mooring Bollard Capacity


Mooring bollard capacity represents the load that the bollard system is designed to resist. However, the bollard is only one component in the complete load path:



Each component must safely transfer the design forces. A correctly rated bollard does not guarantee an adequate mooring point if the anchor bolts, concrete foundation, or supporting structure cannot resist the same loads.


ESC Steel supplies marine mooring bollards in a range of configurations and capacities for ports, harbors, terminals, jetties, quay walls, and other waterfront infrastructure. Engineering support is also available for bollard selection, load verification, and project-specific configurations.


Marine mooring bollard securing a cargo vessel at a port berth


Start with the Design Vessel and Site Conditions


Bollard selection begins with understanding the vessels expected to use the berth. Vessel displacement, length overall, beam, draft, freeboard, projected areas, and mooring arrangement can all influence the forces that must be resisted.


While vessel displacement is useful during preliminary planning, it should not be treated as the sole basis for determining bollard capacity.


Environmental conditions are equally important. Wind, current, waves, swell, tides, and abnormal environmental loading can increase vessel movement and mooring-line forces. Changes in draft during loading and unloading can also alter line geometry and load distribution.




Consider the Mooring Arrangement and Line Angles


The arrangement of head lines, stern lines, breast lines, and spring lines affects how forces are distributed between individual bollards.


Bollard spacing, vessel fairlead locations, mooring-line characteristics, and horizontal and vertical line angles can significantly affect the load at each mooring point. This is why bollard type, and rated capacity should be considered together.



Different configurations suit different vessel sizes, line arrangements, tidal conditions, and operational requirements. For example, Single Bitt Bollards are particularly suited to large tidal variations and steeper mooring-line angles, while T-Head and T-Horn configurations can accommodate higher line-load angles than some Kidney and Single Bitt designs.


Marine fenders and mooring bollards for port and waterfront infrastructure


Determine the Required Bollard Capacity


Once vessel characteristics, environmental forces, and mooring geometry are established, the resulting loads can be evaluated to determine the demand at each mooring point.


The selected capacity should consider the governing mooring-line load, horizontal and vertical force components, load distribution, applicable design factors, and expected operating conditions.


Approximate relationships between ship displacement and bollard capacity can be useful during preliminary planning, but ESC Steel recommends calculating actual mooring loads where possible. Its published guidance also notes that capacity should be increased by 25% or greater when adverse weather conditions are expected at the berth.


The final bollard rating should therefore be based on project-specific engineering analysis and applicable design requirements, rather than a simple vessel-displacement-to-bollard-capacity table.


Diagram showing how mooring line tension creates horizontal and vertical load components on a marine bollard


Verify the Foundation and Anchoring System


Selecting the bollard is only part of the engineering process. The anchor bolts, concrete foundation, and supporting quay, pier, wharf, dolphin, or deck must also safely transfer the design forces.


Replacing an existing bollard with a higher-capacity unit does not automatically increase the capacity of the complete mooring point. The existing anchoring system and supporting structure must also be evaluated.



Material and Corrosion Protection


Mooring bollards operate in aggressive marine environments where saltwater exposure, moisture, corrosion, impact, and mechanical wear can affect long-term performance.


Material specification and protective coating should therefore be considered together with bollard capacity and geometry.


ESC Steel offers ductile cast iron and cast steel bollards with published material options referencing standards including ASTM A536 and ASTM A148, along with BS EN, ISO, and other specifications. High-performance epoxy and project-specific protective coating systems can also be provided.


Yellow marine mooring bollards securing a cargo vessel alongside a concrete wharf


Selecting Mooring Bollards for U.S. Marine Projects


ESC Marine & Foundation Piling Catalog ​

Selecting the correct mooring bollard requires more than matching a vessel's displacement to a nominal bollard capacity. The design vessel, environmental conditions, mooring geometry, line loads, anchoring system, and supporting structure must work together as a complete system.


ESC Steel supplies marine mooring bollards as part of its broader range of piling, marine, and waterfront infrastructure solutions for North America. The company also provides engineering support to assist with bollard selection, load verification, and custom configurations for project-specific requirements.


Providing vessel information, berth drawings, environmental design conditions, required capacity, and applicable design criteria early in the project can help establish an appropriate mooring bollard solution.



✉️ info@escsteel.com or 📞 ᴜꜱᴀ (980) 689 4389 ᴄᴀɴᴀᴅᴀ +1 (902) 442 0800






bottom of page